Skip to content

Opportunity overview

Active Federal PPRA / EPADS Official source

Purchase of Chemical and Consumables for BMES Deptt out of Lab Budget FY 2026–27

NUST-SMME (National University of Science & Technology (NUST))

Reference: P179082

Tender information

Published
Submission deadline
Not specified
Procurement method
Petty Purchase
Procuring agency
NUST-SMME (National University of Science & Technology (NUST))
Bid security
0.00 PKR

Tender description

  • Lot 1
  • Disposable ECG Electrodes
  • Surgical Tape
  • NaOH (Soduim Hydroxide)
  • Syringe Filters 0.22µm / 0.45µm
  • Bread Board
  • Battery 9V
  • Distilled Water
  • Beaker 500ml
  • Beaker 1000ml
  • Surgical Gloves
  • Ethanol Solution
  • Soldering Wire
  • Antibacterial Cleaner
  • Disposable Spirometer Mouthpieces
  • Centrifuge Tubes 15ml
  • Petri dishes 90mm
  • WD 40
  • Test Tube 5ml
  • Flask 500ml
  • Disposable Face Shield
  • Filter paper
  • Glue Gun Stick
  • Disposable Needles
  • Alcohol Pads
  • Silicon Paste

Technical Specifications

Lot 1 — Disposable ECG Electrodes

Specification
They are designed for surface monitoring or needle/ intramuscular recording

Lot 1 — Surgical Tape

Specification
vary by material, adhesive strength, and intended medical use

Lot 1 — NaOH (Soduim Hydroxide)

Specification
A white, odourless, and highly caustic solid or concentrated liquid with a molecular weight of 39.997 g/mol

Lot 1 — Syringe Filters 0.22µm / 0.45µm

Specification
Single-use, membrane-based devices used to remove particulate impurities from liquid or gas samples before analysis

Lot 1 — Bread Board

Specification
830 total tie points, a 0.1-inch (2.54 mm) hole grid spacing, and an ABS plastic body rated for 5V at 1A

Lot 1 — Battery 9V

Specification
Nominal voltage of 9 volts and measures approximately 48.5 × 26.5 × 17.5 mm in a rectangular PP3 size

Lot 1 — Distilled Water

Specification
Purified liquid with near-zero minerals and impurities, meeting strict physical, chemical, and microbiological standards

Lot 1 — Beaker 500ml

Specification
A standard 500ml low-form (Griffin) laboratory glass beaker made of borosilicate 3.3 glass

Lot 1 — Beaker 1000ml

Specification
A standard 1000ml (1 liter) low-form (Griffin) glass beaker has an approximate outer diameter of 105 mm and a height of 145 mm

Lot 1 — Surgical Gloves

Specification
Sterility, precise sizing, anatomical fit, and high tensile strength

Lot 1 — Ethanol Solution

Specification
70% weight/volume ethanol and 28–32% volume/volume water (Bottle)

Lot 1 — Soldering Wire

Specification
Alloy composition of 60/40 (Tin/Lead) or 63/37 (Sn/Pb)

Lot 1 — Antibacterial Cleaner

Specification
Active ingredients like Benzalkonium Chloride, and required surface contact times

Lot 1 — Disposable Spirometer Mouthpieces

Specification
Single-use patient interfaces typically made of white spiral-wound cardboard or medical-grade plastic

Lot 1 — Centrifuge Tubes 15ml

Specification
Centrifuge tubes measure approximately 17 mm in outer diameter and 120 mm in total length

Lot 1 — Petri dishes 90mm

Specification
Nominal diameter of 90 mm, a depth or height ranging from 14 mm to 16.1 mm, and a typical growth/culture surface area of roughly 55 to 64 cm²

Lot 1 — WD 40

Specification
Light amber, low-viscosity liquid and aerosol with a characteristic pleasant odor (Bottle)

Lot 1 — Test Tube 5ml

Specification
12 mm x 75 mm in outer diameter and length, with a round bottom and a 5 ml nominal capacity

Lot 1 — Flask 500ml

Specification
500 mL volumetric or Erlenmeyer glass flask made of borosilicate 3.3 glass

Lot 1 — Disposable Face Shield

Specification
An optically clear, anti-fog plastic visor attached to a foam forehead cushion and an elastic head strap

Lot 1 — Filter paper

Specification
Particle retention pore size, filtration speed, and ash content (Pkt)

Lot 1 — Glue Gun Stick

Specification
Categorized primarily by their diameter and length to match specific mini, standard, or industrial hot glue guns

Lot 1 — Disposable Needles

Specification
Vary fundamentally depending on whether they are intended for medical/hypodermic applications, sewing machines, or surgical sutures

Lot 1 — Alcohol Pads

Specification
Saturated with 70% isopropyl alcohol and 30% purified water for effective antiseptic cleansing prior to injections or minor first-aid

Lot 1 — Silicon Paste

Specification
Thick, hydrophobic silicone-oil-based compound used for lubrication, electrical insulation, and thermal conduction

Official source

Always confirm dates, documents, and submission instructions on the originating portal.

View original tender on Federal PPRA / EPADS